Franklin Electric complete 4 in submersible pumps, each a pump end factory-assembled on a Franklin stainless motor, 5–90 GPM and 1/2–5 HP. Tri-Seal handles sandy water, 3200 Series fits tight and deep-set wells, and High Capacity covers 35–45 GPM. QuickPAK packages hold constant pressure. Pump ends carry UL 778, CSA and NSF/ANSI 61 listings. We size the pump, control box and cable to your well. Call 1-888.510.4036.
Franklin Electric 4 in E-Series Environmental Submersible Pump - 2-Wire, 10-20 GPM
Price
From $1,122.09
Franklin Electric Submersible Well Pumps
Franklin Electric · 4 in Submersible
Franklin Electric Submersible Well Pumps
Complete 4 in pumps and constant pressure packages for homes, farms and light commercial wells — pump end and motor assembled, chosen by flow and head.
9Pump Families
5–90GPM
1/2–5HP
1,250 ftLift at 50 PSI
NSF/ANSI 61Pump Ends
These are Franklin Electric’s complete 4 in submersible pumps, each a Franklin pump end factory-assembled on a Franklin stainless motor: 3200 Series for low-yield and tight wells, Series V and Tri-Seal for everyday home and farm supply, High Capacity for 35–45 GPM, QuickPAK constant pressure packages, plus E-Series effluent and C1 cistern pumps.
We supply every build on this page with engineering-led sizing: send the well depth, pumping level and the pressure you want, and we will match the pump, control box and cable before you order. Call 1-888.510.4036 or email sales@watermainsupply.com. Genuine Franklin Electric equipment, factory-new in original packaging — sold and supported by Watermain Supply, an independent industrial supplier.
Will It Work for Me?
The four questions that decide a submersible job.
Warranty
4 in complete pumps carry Franklin’s limited warranty for 1 year from the date of original purchase. QuickPAK packages: 12 months from installation, no more than 24 months from manufacture. Franklin voids motor warranty if non-Franklin leads are used.
Reliability
Tri-Seal floating stages keep a positive seal as the well carries sand; the 3200 Series uses a hex rubber bearing and ceramic shaft sleeve that pass abrasives. Every pump runs on a Franklin stainless motor with hermetically sealed windings.
Fit
4 in or larger wells; the 3200 Series fits encrusted or reduced 4 in wells. 115/230 V single-phase: 2-wire builds need no control box, 3-wire builds need the matching Franklin control box. QuickPAKs run from 208/230 V single-phase.
Size It Now
Work out flow and total dynamic head in two minutes, or call 1-888.510.4036.
Three families cover most residential and farm wells.
Tri-Seal
10–25 GPM · sandy and abrasive wells
10–25GPM
1/2–1.5HP
608 ftMax Head
2 or 3Wire
Franklin’s patented floating-stage design: each stainless hub floats with its impeller and holds a positive seal, so efficiency holds up as the stages see sand.
Every part of the pump end, cable guard included, sits within the motor diameter — the pump for an encrusted or tight 4 in well, with staging tuned for deep settings.
Hex rubber bearing and ceramic shaft sleeve pass sand
Pump, three-phase motor and SubDrive variable frequency drive selected as one package. The drive holds the pressure you set as taps open and close, with soft start and dry-run protection.
SubDrive (to 3 HP) or MagForce permanent-magnet motor (to 5 HP)
Factory set 50 PSI, adjustable 25–80 PSI
FE Connect app on SubDrive Connect builds
Best for Homes that want city-style pressure from a well.
Quick rule: Pick the flow class first (a home typically needs 8–12 GPM, a large home or small farm 15–25), then the HP that reaches your total dynamic head at that flow in the listing’s Models table. Sand in the water points to Tri-Seal; under 10 GPM or a tight casing points to 3200 Series; even pressure at every tap points to QuickPAK.
Franklin vs A.Y. McDonald vs Grundfos — 10 GPM Class
The closest equivalents we list, from each product page on this site.
Spec
Franklin Tri-Seal
A.Y. McDonald 22000 K
Grundfos 10 SQ
Flow
10–25 GPM classes
10 GPM class
3–15 GPM range
HP
1/2–1.5
1/2–1.5
1/2–1.5
Head (as published)
608 ft max
171–392 ft at 10 GPM; 591 ft shut-off
110–370 ft nominal TDH
Motor and control
Franklin 4 in stainless; 3-wire needs control box
Baker 4 in stainless; 3-wire needs control box
Permanent-magnet motor, protection built in, no control box
Verdict: A.Y. McDonald wins on warranty — 5 years from manufacture in potable water against Franklin’s 1 year from purchase. Grundfos SQ wins in a 3 in well and where you want soft start and dry-run protection inside the motor with no control box. Franklin wins on abrasive water with Tri-Seal floating stages, and on range: one maker for 5–90 GPM pumps, the motor, the control box, Pumptec protection and constant pressure drives.
Two numbers decide the pump: flow and total dynamic head (TDH).
TDH = pumping water level + height from the well head to the pressure tank + pressure in psi × 2.31 + pipe friction. Read the result against the head each build delivers at your flow class in the listing’s Models table, then pick the first HP that clears it.
Worked example: Pumping level 180 ft, tank 10 ft above the well head, 50 psi cut-out (50 × 2.31 = 116 ft), 15 ft friction. TDH = 180 + 10 + 116 + 15 = 321 ft at 10 GPM. Choose a 10 GPM build rated at 321 ft or more at 10 GPM, and size the drop cable from Franklin’s motor cable chart.
Send the well depth, pumping level, flow and pressure. We work the total dynamic head and match pump end, motor, control and cable size before you order.
Straight answers across brands
We also supply A.Y. McDonald, Grundfos and DAB submersibles. If Franklin is not the right fit for the well, we will say so and show you what is.
Account terms
Contractor, well driller and municipal accounts on approved credit. Ask us to set one up.
Parts and aftermarket
Motor leads, couplings, check valves, pump and motor repair parts and drive accessories are listed alongside the pumps.
Complete well in one order
Pump, control box, protection, check valves and leads on one order and one invoice.
Houston based, Gulf Coast service
We size, quote and support from Houston for drillers and contractors across the Gulf Coast and beyond.
Frequently Asked Questions
What warranty comes with a Franklin 4 in submersible pump?
Franklin’s limited warranty covers its 4 in complete pumps for 1 year from the date of original purchase. QuickPAK packages are covered for 12 months from installation, no more than 24 months from manufacture. Franklin voids motor warranty if non-Franklin leads are used.
Do I need a control box?
Only for 3-wire builds. 2-wire builds carry the start components inside the motor. Each 3-wire build lists the matching Franklin control box in its Models table.
2-wire or 3-wire — which should I choose?
2-wire is simpler to install with nothing above ground. 3-wire puts the start components in an above-ground box that is easy to service and gives more starting torque on larger pumps.
What size pump does my house need?
Most homes need 8–12 GPM. The HP depends on total dynamic head: pumping level, lift to the tank, pressure × 2.31 and friction. The Submersible Calculator works it out, or call us with the well log.
My well makes sand. Which Franklin pump?
Tri-Seal. Its floating stages keep a positive seal as the stages see abrasives. The 3200 Series also passes sand on a hex rubber bearing and ceramic shaft sleeve.
What is a QuickPAK?
A Franklin pump, motor and SubDrive variable frequency drive sold as one package. The drive holds a set pressure, factory set at 50 PSI, as demand changes.
Can I buy the pump end or motor alone?
Yes. The Series V, Tri-Seal, 3200, High Capacity and E-Series hydraulics are also sold as pump ends, and Franklin 4 in motors are sold separately, so a failed half can be replaced on its own.
Will it fit a 4 in well?
Yes, these are 4 in pumps. The 3200 Series is the slimmest at 3.75 in, for encrusted or reduced 4 in casings.
Ready to Size Your Well?
Send the well depth, pumping level and pressure you need. We will match the pump, control box and cable.
Technical data on this page is taken from Franklin Electric product literature and is subject to change by the manufacturer. Confirm against the current installation manual before specifying.
Franklin Electric, SubDrive, MonoDrive, QuickPAK, SolarPAK, Fhoton, MagForce, Tri-Seal, Pumptec and SubMonitor are trademarks of Franklin Electric Co., Inc. Grundfos and SQ are trademarks of Grundfos Holding A/S. A.Y. McDonald and Baker are trademarks of A.Y. McDonald Mfg. Co. used here for product identification only.
Watermain Supply is a DBA of E4 Industrial LLC, an independent industrial supplier based in Houston, Texas.
Choosing a selection results in a full page refresh.