Menu
Product variant with selected options does not exist!
Vertical, multistage centrifugal pump with suction and discharge ports on the same level. CRN is the AISI 316 grade of the CR platform: every wetted part — pump head, base, chambers, impellers, shaft and sleeves — is AISI 316. Because the ports share a centreline, the pump installs in a straight pipe run without an offset.
The CRN 10 frame is rated at 53.3 GPM. The family number is Grundfos’s nominal duty in cubic metres per hour, not a GPM figure — size the pump from the rated head table below, not from the model number.
3 models are offered, from CRN 10-14 to CRN 10-17, covering 15 HP on NEMA 254TC C-face open drip-proof (ODP) motors. Adding stages raises head at the same flow without changing the footprint. Connections are 2 in Victaulic grooved, or 2 in ANSI 300 lb flanged. Both are rated 362 psi maximum operating pressure.
Why 316 rather than 304. The hydraulics are shared across CR, CRI and CRN, so a CRN 10-16 and the matching CR or CRI model have the same rated duty point. What changes is corrosion resistance. The molybdenum in AISI 316 is what resists chloride pitting, so CRN is the grade for chloride-bearing water, softened or brackish supplies, coastal installations, and process liquids that would pit 304. Where chlorides are not the issue, CRI in 304 does the same hydraulic job for less money, and CR in cast iron less again. For seawater and stronger chloride duty Grundfos offers the CRT range in titanium.
Find the head you need in feet and pick the model that meets it at 53.3 GPM. Rated head is the duty point at rated flow; max head is the shut-off ceiling at zero flow, not a working point.
| Model | HP | Rated flow - GPM | Rated head - ft | Max head - ft |
|---|---|---|---|---|
| CRN 10-14 | 15 | 53.3 | 512.5 | 669.3 |
| CRN 10-16 | 15 | 53.3 | 603.7 | 771 |
| CRN 10-17 | 15 | 53.3 | 638.2 | 817 |
Figures are Grundfos published data for 60 Hz at the rated duty point. For a duty between two models, or for flows away from 53.3 GPM, ask us to size it against the published curve.
| Model | HP | Voltage & Phase | Connection & Seal | Part No. |
|---|---|---|---|---|
| CRN 10-14 | 15 | 208-230/460V 3Ph | Victaulic - HQQE | 99917422 |
| CRN 10-14 | 15 | 208-230/460V 3Ph | Victaulic - HQQV | 99917425 |
| CRN 10-14 | 15 | 208-230/460V 3Ph | ANSI Flanged - HQQE | 99917428 |
| CRN 10-14 | 15 | 208-230/460V 3Ph | ANSI Flanged - HQQV | 99917432 |
| CRN 10-16 | 15 | 208-230/460V 3Ph | Victaulic - HQQE | 99917423 |
| CRN 10-16 | 15 | 208-230/460V 3Ph | Victaulic - HQQV | 99917426 |
| CRN 10-16 | 15 | 208-230/460V 3Ph | ANSI Flanged - HQQE | 99917430 |
| CRN 10-16 | 15 | 208-230/460V 3Ph | ANSI Flanged - HQQV | 99917433 |
| CRN 10-17 | 15 | 208-230/460V 3Ph | Victaulic - HQQE | 99917424 |
| CRN 10-17 | 15 | 208-230/460V 3Ph | Victaulic - HQQV | 99917427 |
| CRN 10-17 | 15 | 208-230/460V 3Ph | ANSI Flanged - HQQE | 99917431 |
| CRN 10-17 | 15 | 208-230/460V 3Ph | ANSI Flanged - HQQV | 99917434 |
Where two voltages are shown, the first is the factory wiring setting. Voltage is changed on the motor terminal board, never at the pressure switch. All models are single phase unless the table states 3Ph.
In the Grundfos type key the final letter is the rubber: E = EPDM, V = FKM. Both options use silicon-carbide faces (QQ) and the same cartridge format.
| Specification | Value |
|---|---|
| Rated flow at 60 Hz | 53.3 GPM |
| Rated head range | 512 to 638 ft |
| Motor power range | 15 HP |
| Motor enclosure | Open drip-proof (ODP), NEMA C-face |
| NEMA frames | 254TC |
| Frequency | 60 Hz |
| Suction and discharge port | 2 in |
| Connection | 2 in Victaulic grooved, or 2 in ANSI 300 lb flanged. Both are rated 362 psi maximum operating pressure |
| Maximum operating pressure | 362 psi |
| Liquid temperature range | −4 °F to 248 °F with HQQE; −4 °F to 194 °F with HQQV |
| Maximum ambient temperature | 104 °F |
| Pumped liquid | Clean, thin, non-explosive liquids without solid particles or fibres |
| Pump orientation | Vertical |
| Drinking water approval | NSF/ANSI 61 |
| Curve tolerance | ISO9906:2012 3B |
| Component | Material |
|---|---|
| Pump head and base | Stainless steel, EN 1.4401 (AISI 316) |
| Chambers and impellers | Stainless steel, EN 1.4401 (AISI 316) |
| Shaft and sleeves | Stainless steel, EN 1.4401 (AISI 316) |
| Shaft seal faces | Silicon carbide / silicon carbide |
| Seal and gasket rubber | EPDM (HQQE) or FKM (HQQV) |
| Bearing | Silicon carbide (SiC) |
| ANSI flange and base plate | Cast iron — does not contact the pumped liquid |
Each part number is a complete pump: pump end, motor, coupling, coupling guard and shaft seal, factory assembled and tested.
Companion connections are ordered separately on both styles. Grundfos supplies the CRN pump with its connection prepared but not with the mating hardware: Victaulic couplings and gaskets for the grooved version, and companion flanges, bolts and gaskets for the ANSI version. Order them with the pump so the job is not held up. The ANSI flanged version uses a cast iron flange and base plate; neither contacts the pumped liquid, so the wetted path stays all 316 stainless.
Motor starters, variable frequency drives, pressure sensors, base plates, foundation bolts and isolation valves are not included. These are fixed-speed pumps; for integrated variable-speed control see the CRNE range.
Select the HP and voltage, then the model, then the connection and seal. Each combination is a distinct Grundfos part number, listed in the table above and shown in the SKU of the selected variant.
The picker shows only the combinations Grundfos publishes.
Product videos are being added to this listing. For a walkthrough in the meantime, email sales@watermainsupply.com.
Sign up for our newsletter and be the first to know about coupons and special promotions.
© 2026, Watermainsupply