{"product_id":"grundfos-sqflex-solar-pump-hydraulic-end","title":"Grundfos SQFlex Solar Pump Hydraulic End","description":"\u003c!-- TABS --\u003e\u003ch5\u003eDescription\u003c\/h5\u003e\u003cdiv class=\"gs\"\u003e\n\u003cdiv class=\"gs-head\"\u003e\n\u003cdiv class=\"gs-eyebrow\"\u003eGRUNDFOS · SQFLEX HYDRAULIC END · MOTOR NOT INCLUDED\u003c\/div\u003e\n\u003cdiv class=\"gs-title\"\u003eSQFlex Hydraulic End\u003c\/div\u003e\n\u003cdiv class=\"gs-sub\"\u003eReplacement pump end for Grundfos SQFlex solar submersible pumps — hydraulic end only, without the MSF 3 motor, cable or controls. Five 3 in helical rotor ends and three 4 in centrifugal ends.\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"gs-badges\"\u003e\n\u003cdiv class=\"gs-badge\"\u003eHydraulic End Only\u003c\/div\u003e\n\u003cdiv class=\"gs-badge\"\u003eFits MSF 3 Motor, 500-3600 rpm\u003c\/div\u003e\n\u003cdiv class=\"gs-badge\"\u003e3 in Helical Rotor: 3, 6 and 11 SQF\u003c\/div\u003e\n\u003cdiv class=\"gs-badge\"\u003e4 in Centrifugal: 35, 45 and 75 SQF\u003c\/div\u003e\n\u003cdiv class=\"gs-badge\"\u003eStainless Steel AISI 304\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"gs-sec\"\u003e\n\u003cdiv class=\"gs-h\"\u003eOverview\u003c\/div\u003e\n\u003cdiv class=\"gs-lead\"\u003e\n\u003cp\u003eThe SQF pump range comprises two pump technologies: the helical rotor pump (3 in) for high heads and small flow rates, and the centrifugal pump (3 in and 4 in) for low heads and large flow rates. The modular pump and motor design facilitates installation and service. These are the hydraulic ends Grundfos lists separately on its 2026 renewables price list — the pump end without the MSF 3 motor — for returning a worn SQFlex pump to service on its existing motor.\u003c\/p\u003e\n\u003cp\u003eHelical rotor pumps cannot be separated from the motor as a unit: if the motor or the pump has to be replaced, the pump must be dismantled, following the Grundfos service instructions summarized below. Centrifugal pump ends detach from the motor at the four nuts on the suction interconnector.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"background:#E1E3E6;border-left:3px solid #B8BDC4;padding:8px 14px;font-size:11.5px;color:#4A4A4F;margin-top:14px;line-height:1.5\"\u003eGenuine Grundfos equipment, factory-new in original packaging — sold and supported by Watermain Supply, an independent industrial supplier.\u003c\/div\u003e\n\u003cdiv class=\"gs-sec\"\u003e\n\u003cdiv class=\"gs-h\"\u003eModels \u0026amp; Part Numbers\u003c\/div\u003e\n\u003cdiv class=\"table-wrapper\"\u003e\u003ctable class=\"gs-tbl\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003ePump type\u003c\/th\u003e\n\u003cth\u003eDischarge\u003c\/th\u003e\n\u003cth\u003eMin. well\u003c\/th\u003e\n\u003cth\u003eComplete pump Part No.\u003c\/th\u003e\n\u003cth\u003eHydraulic end Part No.\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e3 SQF-2\u003c\/td\u003e\n\u003ctd\u003e3 in Helical Rotor\u003c\/td\u003e\n\u003ctd\u003e1 in NPT\u003c\/td\u003e\n\u003ctd\u003e3 in\u003c\/td\u003e\n\u003ctd\u003e95027332\u003c\/td\u003e\n\u003ctd\u003e95027407\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e3 SQF-3\u003c\/td\u003e\n\u003ctd\u003e3 in Helical Rotor\u003c\/td\u003e\n\u003ctd\u003e1 in NPT\u003c\/td\u003e\n\u003ctd\u003e3 in\u003c\/td\u003e\n\u003ctd\u003e95027333\u003c\/td\u003e\n\u003ctd\u003e95027410\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e6 SQF-2\u003c\/td\u003e\n\u003ctd\u003e3 in Helical Rotor\u003c\/td\u003e\n\u003ctd\u003e1 in NPT\u003c\/td\u003e\n\u003ctd\u003e3 in\u003c\/td\u003e\n\u003ctd\u003e95027334\u003c\/td\u003e\n\u003ctd\u003e95027413\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e6 SQF-3\u003c\/td\u003e\n\u003ctd\u003e3 in Helical Rotor\u003c\/td\u003e\n\u003ctd\u003e1 in NPT\u003c\/td\u003e\n\u003ctd\u003e3 in\u003c\/td\u003e\n\u003ctd\u003e96834840\u003c\/td\u003e\n\u003ctd\u003e96834837\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e11 SQF-2\u003c\/td\u003e\n\u003ctd\u003e3 in Helical Rotor\u003c\/td\u003e\n\u003ctd\u003e1-1\/4 in NPT\u003c\/td\u003e\n\u003ctd\u003e3 in\u003c\/td\u003e\n\u003ctd\u003e95027335\u003c\/td\u003e\n\u003ctd\u003e95027416\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e35 SQF-4\u003c\/td\u003e\n\u003ctd\u003e4 in Centrifugal\u003c\/td\u003e\n\u003ctd\u003e2 in NPT\u003c\/td\u003e\n\u003ctd\u003e4 in\u003c\/td\u003e\n\u003ctd\u003e98994960\u003c\/td\u003e\n\u003ctd\u003e98994956\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e45 SQF-3\u003c\/td\u003e\n\u003ctd\u003e4 in Centrifugal\u003c\/td\u003e\n\u003ctd\u003e2 in NPT\u003c\/td\u003e\n\u003ctd\u003e4 in\u003c\/td\u003e\n\u003ctd\u003e98994951\u003c\/td\u003e\n\u003ctd\u003e98994939\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e75 SQF-3\u003c\/td\u003e\n\u003ctd\u003e4 in Centrifugal\u003c\/td\u003e\n\u003ctd\u003e2 in NPT\u003c\/td\u003e\n\u003ctd\u003e4 in\u003c\/td\u003e\n\u003ctd\u003e98994964\u003c\/td\u003e\n\u003ctd\u003e98994963\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\u003cp style=\"font-size:12.5px;color:#9B9EA3;margin-top:8px;line-height:1.55\"\u003eOrder the hydraulic end number in the last column. The complete pump number is shown so you can match the nameplate: on helical rotor pumps the nameplate is engraved into the pump sleeve; on centrifugal pumps it is attached to the suction interconnector. 75 SQF-3 is shown as 77 SQF-3 in Grundfos data booklets. All eight models run on the 1400 W MSF 3 motor, 500-3600 rpm.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"gs-sec\"\u003e\n\u003cdiv class=\"gs-h\"\u003eMaterials\u003c\/div\u003e\n\u003cdiv class=\"table-wrapper\"\u003e\u003ctable class=\"gs-tbl\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eHelical rotor component\u003c\/th\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003cth\u003eEN\/DIN\u003c\/th\u003e\n\u003cth\u003eAISI\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eValve casing, valve cup, valve guide\u003c\/td\u003e\n\u003ctd\u003ePolyamide\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutlet chamber\u003c\/td\u003e\n\u003ctd\u003eStainless steel\u003c\/td\u003e\n\u003ctd\u003e1.4301\u003c\/td\u003e\n\u003ctd\u003e304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eValve seat\u003c\/td\u003e\n\u003ctd\u003eSilicone (LSR)\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eUpper flange\u003c\/td\u003e\n\u003ctd\u003eStainless steel\u003c\/td\u003e\n\u003ctd\u003e1.4401\u003c\/td\u003e\n\u003ctd\u003e316\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePump stator\u003c\/td\u003e\n\u003ctd\u003eStainless steel \/ EPDM\u003c\/td\u003e\n\u003ctd\u003e1.4301\u003c\/td\u003e\n\u003ctd\u003e304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePump rotor\u003c\/td\u003e\n\u003ctd\u003eStainless steel\u003c\/td\u003e\n\u003ctd\u003e1.4401\u003c\/td\u003e\n\u003ctd\u003e316\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTorsion shaft\u003c\/td\u003e\n\u003ctd\u003eStainless steel\u003c\/td\u003e\n\u003ctd\u003e1.4401\u003c\/td\u003e\n\u003ctd\u003e316\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSleeve\u003c\/td\u003e\n\u003ctd\u003eStainless steel\u003c\/td\u003e\n\u003ctd\u003e1.4301\u003c\/td\u003e\n\u003ctd\u003e304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSand slinger\u003c\/td\u003e\n\u003ctd\u003eNBR\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\u003cdiv class=\"table-wrapper\"\u003e\u003ctable class=\"gs-tbl\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003e4 in centrifugal component\u003c\/th\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003cth\u003eEN\u003c\/th\u003e\n\u003cth\u003eAISI\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eValve casing, valve cup\u003c\/td\u003e\n\u003ctd\u003eCast stainless steel\u003c\/td\u003e\n\u003ctd\u003e1.4301\u003c\/td\u003e\n\u003ctd\u003e304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eValve seat\u003c\/td\u003e\n\u003ctd\u003eNBR-FKM\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeck ring\u003c\/td\u003e\n\u003ctd\u003eTPU \/ PPS-FKM\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBearing\u003c\/td\u003e\n\u003ctd\u003eLSR \/ FKM\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eChamber, impeller\u003c\/td\u003e\n\u003ctd\u003eStainless steel\u003c\/td\u003e\n\u003ctd\u003e1.4301\u003c\/td\u003e\n\u003ctd\u003e304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInlet interconnector\u003c\/td\u003e\n\u003ctd\u003eCast stainless steel\u003c\/td\u003e\n\u003ctd\u003e1.4308\u003c\/td\u003e\n\u003ctd\u003eCF8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eStrainer, strap, cable guard\u003c\/td\u003e\n\u003ctd\u003eStainless steel\u003c\/td\u003e\n\u003ctd\u003e1.4301\u003c\/td\u003e\n\u003ctd\u003e304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShaft complete\u003c\/td\u003e\n\u003ctd\u003eStainless steel\u003c\/td\u003e\n\u003ctd\u003e1.4057\u003c\/td\u003e\n\u003ctd\u003e431\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\u003cp style=\"font-size:12.5px;color:#9B9EA3;margin-top:8px;line-height:1.55\"\u003eFrom the Grundfos SQFlex data booklet 92552657, North America 60 Hz, 07\/2021.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"gs-sec\"\u003e\n\u003cdiv class=\"gs-h\"\u003eFitting the Hydraulic End to the Motor\u003c\/div\u003e\n\u003cdiv class=\"gs-lead\"\u003e\n\u003cp\u003e\u003cstrong\u003eBefore assembly.\u003c\/strong\u003e Disconnect the electricity supply to the motor. Clean all parts and check them for fractures and wear, replace defective parts, and moisten rubber parts with soapy water before fitting them. When fixing the motor in a vice, tighten only on the 30 mm wide area starting 37 mm from the upper edge of the motor sleeve. Before connecting the pump to the motor, fill the motor with Grundfos motor liquid: stand the motor vertically with an inclination of about 10°, remove the filling plug, inject motor liquid with a filling syringe, move the motor from side to side to let air escape, then refit the filling plug and make sure it is tight.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHelical rotor pump — assembly.\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eFit the pump rotor to the torsion shaft and tighten to the correct torque, holding the pump rotor with a pipe wrench on the cylindrical part below the rotor.\u003c\/li\u003e\n\u003cli\u003eFit the torsion shaft to the motor shaft and tighten to the correct torque.\u003c\/li\u003e\n\u003cli\u003eFit the pump stator, with the conical stator inlet against the strainer, into the outer sleeve.\u003c\/li\u003e\n\u003cli\u003eFit the flange into the outer sleeve and press it onto the upper part of the stator, fixing the stator in the centre of the sleeve. On 11 SQF-2, turn the flange with the even surface against the stator.\u003c\/li\u003e\n\u003cli\u003eFit the discharge chamber with valve casing complete — grease the thread — and tighten to the correct torque, holding the pump on the weld just above the upper strainer.\u003c\/li\u003e\n\u003cli\u003eMoisten the pump rotor with clean water, fit the pump on the motor and tighten to the correct torque.\u003c\/li\u003e\n\u003cli\u003eRefit the end cover with socket and cable if it was removed, then the cable guard.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003eCentrifugal pump — fitting pump to motor.\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eScrew the shaft end onto the motor shaft and push it home. Adjust the height to 88.15 mm ±0.2 mm with the measuring template, tighten the nut to the correct torque and check the height again.\u003c\/li\u003e\n\u003cli\u003eFit the supporting ring and the spline protector.\u003c\/li\u003e\n\u003cli\u003eFit the connecting piece and tighten with a pipe wrench.\u003c\/li\u003e\n\u003cli\u003eFit the pump to the motor with the cable recesses in the suction interconnector and the connecting piece next to each other. Fit the four nuts and tighten diagonally to the correct torque.\u003c\/li\u003e\n\u003cli\u003eRefit the end cover with cable if it was removed, then the cable guards.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"table-wrapper\"\u003e\u003ctable class=\"gs-tbl\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eJoint\u003c\/th\u003e\n\u003cth\u003ePump type\u003c\/th\u003e\n\u003cth\u003eTorque\u003c\/th\u003e\n\u003cth\u003eLubricant\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePump \/ motor\u003c\/td\u003e\n\u003ctd\u003eHelical\u003c\/td\u003e\n\u003ctd\u003e55 Nm (41 lb-ft)\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDischarge chamber (lubricate the thread)\u003c\/td\u003e\n\u003ctd\u003eHelical\u003c\/td\u003e\n\u003ctd\u003e100 Nm (74 lb-ft)\u003c\/td\u003e\n\u003ctd\u003eRocol Sapphire Aqua-Sil\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePump rotor \/ torsion shaft\u003c\/td\u003e\n\u003ctd\u003eHelical\u003c\/td\u003e\n\u003ctd\u003e18 Nm (13 lb-ft)\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTorsion shaft \/ motor shaft\u003c\/td\u003e\n\u003ctd\u003eHelical\u003c\/td\u003e\n\u003ctd\u003e18 Nm (13 lb-ft)\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShaft screw or nut (pos. 19)\u003c\/td\u003e\n\u003ctd\u003eCentrifugal\u003c\/td\u003e\n\u003ctd\u003e18 Nm (13 lb-ft)\u003c\/td\u003e\n\u003ctd\u003eGardolube L 6034\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePump \/ motor nuts (pos. 19a)\u003c\/td\u003e\n\u003ctd\u003eCentrifugal\u003c\/td\u003e\n\u003ctd\u003e18 Nm (13 lb-ft)\u003c\/td\u003e\n\u003ctd\u003eGardolube L 6034\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNut (pos. 19b)\u003c\/td\u003e\n\u003ctd\u003eCentrifugal, splined shaft\u003c\/td\u003e\n\u003ctd\u003e11 Nm (8 lb-ft)\u003c\/td\u003e\n\u003ctd\u003eGardolube L 6034\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShaft end nut (pos. 24)\u003c\/td\u003e\n\u003ctd\u003eCentrifugal\u003c\/td\u003e\n\u003ctd\u003e18 Nm (13 lb-ft)\u003c\/td\u003e\n\u003ctd\u003e–\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEnd cover nuts\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e1.5 Nm (1.1 lb-ft)\u003c\/td\u003e\n\u003ctd\u003eRocol on the end cover with cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\u003cp style=\"font-size:12.5px;color:#9B9EA3;margin-top:8px;line-height:1.55\"\u003eSummarized from the Grundfos SQFlex service instructions (96547280), which carry the exploded views, position numbers and the special service tools. It is not necessary to lubricate screws and nuts treated with Delta Seal. After assembly, test head and flow to the Grundfos test specification before the pump goes back in the well.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"gs-note\"\u003e\n\u003cb\u003eBefore You Order\u003c\/b\u003eA hydraulic end is not a working pump: it has no motor, no cable and no water level electrode. Match the model on the nameplate of the pump being repaired and order the same model — the hydraulic end sets the duty, and the pump delivers its maximum performance against the limits of the motor already installed. For a complete pump see the \u003ca href=\"\/products\/grundfos-sqflex-helical-rotor-solar-submersible-pump\"\u003eSQFlex helical rotor\u003c\/a\u003e and \u003ca href=\"\/products\/grundfos-sqflex-4-in-centrifugal-solar-submersible-pump\"\u003eSQFlex 4 in\u003c\/a\u003e listings. Supplied for installation in the United States and shipped to U.S. addresses only.\u003c\/div\u003e\n\u003cdiv class=\"gs-contact\"\u003eFor engineering-led sizing and selection support or a factory submittal, email \u003ca href=\"mailto:sales@watermainsupply.com\"\u003esales@watermainsupply.com\u003c\/a\u003e or call \u003ca href=\"tel:18885104036\"\u003e1-888.510.4036\u003c\/a\u003e.\u003cbr\u003e© Watermain Supply — A division of E4 Industrial LLC\u003c\/div\u003e\n\u003c\/div\u003e\u003ch5\u003eData Sheet\u003c\/h5\u003e\u003cdiv class=\"gs\"\u003e\u003cdiv class=\"gs-dl\"\u003e\n\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0264\/1913\/4527\/files\/L-SQ-TL-031_1012_SQFlexServInstr.pdf?v=1789850918\" target=\"_blank\" rel=\"noopener\"\u003eSQFlex Service Instructions (L-SQ-TL-031, 10\/2012)\u003c\/a\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0264\/1913\/4527\/files\/sqflex_SI_US.pdf?v=1789850918\" target=\"_blank\" rel=\"noopener\"\u003eSQFlex Service Instructions — Earlier Edition (96547280, 02\/2006)\u003c\/a\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0264\/1913\/4527\/files\/96488862_12.2023_Service_Kit_Catalogue_2023_Online_SQFlex.pdf?v=1789850917\" target=\"_blank\" rel=\"noopener\"\u003eSQFlex Service Kit Catalogue (96488862, 12\/2023)\u003c\/a\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0264\/1913\/4527\/files\/DN000993_0421_SQFlex_Range-8.5x11-Farm-USA-Final-1.pdf?v=1789850918\" target=\"_blank\" rel=\"noopener\"\u003eSQFlex Range Brochure — Models, Range Chart and Controls (DN000993, 04\/2021)\u003c\/a\u003e\n\u003c\/div\u003e\u003c\/div\u003e\u003ch5\u003eVideos\u003c\/h5\u003e\u003cdiv class=\"gs\"\u003e\u003cdiv class=\"gs-sec\" style=\"margin-top:6px\"\u003e\u003cp style=\"font-size:13px;color:#9B9EA3\"\u003eProduct videos are being added to this listing. For a walkthrough in the meantime, email sales@watermainsupply.com.\u003c\/p\u003e\u003c\/div\u003e\u003c\/div\u003e\u003c!-- \/TABS --\u003e","brand":"Grundfos","offers":[{"title":"3 SQF-2 - Pump End Only","offer_id":47538164826287,"sku":"95027407","price":1534.58,"currency_code":"USD","in_stock":true},{"title":"3 SQF-3 - Pump End Only","offer_id":47538164859055,"sku":"95027410","price":1534.58,"currency_code":"USD","in_stock":true},{"title":"6 SQF-2 - Pump End Only","offer_id":47538164891823,"sku":"95027413","price":1534.58,"currency_code":"USD","in_stock":true},{"title":"6 SQF-3 - Pump End Only","offer_id":47538164924591,"sku":"96834837","price":1534.58,"currency_code":"USD","in_stock":true},{"title":"11 SQF-2 - Pump End Only","offer_id":47538164957359,"sku":"95027416","price":1534.58,"currency_code":"USD","in_stock":true},{"title":"35 SQF-4 - Pump End Only","offer_id":47538164990127,"sku":"98994956","price":1534.58,"currency_code":"USD","in_stock":true},{"title":"45 SQF-3 - Pump End Only","offer_id":47538165022895,"sku":"98994939","price":1534.58,"currency_code":"USD","in_stock":true},{"title":"75 SQF-3 - Pump End Only","offer_id":47538165055663,"sku":"98994963","price":1534.58,"currency_code":"USD","in_stock":true}],"url":"https:\/\/watermainsupply.com\/products\/grundfos-sqflex-solar-pump-hydraulic-end","provider":"Watermainsupply","version":"1.0","type":"link"}